Pipe Reducer Manufacturers in Pune, Navi Mumbai, Nagpur – Eccentric Reducer | Concentric Reducer
“We are Your Best Source For Pipe Reducer Fittings is Classified Below:-
Concentric reducers reduce the pipe in the center. So, if you’re looking at the reducer head-on, you can see the smaller section is formed in the direct center of the larger side. In Concentric Reducer Manufacturers Pune, Navi Mumbai, Nagpur the reduction of the pipe size is achieved by decreasing the diameter of the fitting at a constant rate over a specified length, maintaining symmetry around the fitting. Concentric Reducers are used to join pipe or tube sections of different diameters on the same axis.
Eccentric reducers reduce the pipe to the side. So, if you’re looking at the reducer head-on, you can see the smaller section is against one side of the larger side. Eccentric Reducer Manufacturers Pune, Navi Mumbai, Nagpur are used at the suction side of pumps to ensure air does not accumulate in the pipe. The gradual accumulation of air in a concentric reducer could result in a large bubble that could eventually cause the pump to stall or cause cavitation when drawn into the pump.
Carbon Steel Pipe Reducer, Eccentric Reducer, Concentric Reducer,ASME/ANSI B16.9, ANSI B16.28, MSS-SP-43 Suppliers in Pune, Navi Mumbai, Nagpur
Stainless Steel Buttweld Reducer Fittings, Carbon Steel Reducer, Alloy Steel Reducer, Duplex Steel Reducer Pipe Fittings,Carbon, Alloy, Stainless Steel, Copper Reducer Manufacturers & Suppliers in Pune, Navi Mumbai, Nagpur
MSI Fittings is ISO and NORSOK approved manufacturers of Stainless Steel Pipe Fittings (ASME B16.9, DIN, EN) in Pune, Navi Mumbai, Nagpur, we are Indian Oil cretified manufacturer of Stainless Steel Flanges (ASTM A182, ASTM A240, ASME, DIN, EN) & Stainless Steel Forged Fittings (ASTM A182, ASME, DIN, EN) in Pune, Navi Mumbai, Nagpur, our Manufacturing Range is Stainless Steel Reducer, Stainless Steel Elbow, Stainless Steel Long/Short Radius Elbows,Stainless Steel LR elbow, Stainless steel SR elbow,Stainless Steel Compression Fittings, Stainless Steel Single Ferrule Fittings, Stainless Steel Double Ferrule Fittings, MSI Fittings is 6th largest Manufacturer of Stainless Steel industrial pipe Fittings in Pune, Navi Mumbai, Nagpur, we are exporter of Stainless Steel Tee’s, Stainless Steel Stub Ends, Stainless Steel Double Flanged Fittings, Stainless Steel Fabricated Fittings, Threaded Stainless Steel Fittings, NPT Fittings, SS 304/304L Pipe Fittings, SS 316/316L Pipe Fittings, SS 316Ti Fittings, Stainless Steel U Bends, Stainless Steel Reducers, Stainless Steel 5D/3D Elbow, Stainless Steel Tube Fittings
Introduction : Pipe Reducer Manufacturers & Supplier in Pune, Navi Mumbai, Nagpur
An ISO 9001:2015 Certified Company, MSI Fittings is a leading manufacturer and supplier of short radius and long radius elbows. We offer our materials with complete certifications and as per international standards. Our production range includes stainless steel elbows, carbon steel elbows, alloy steel elbows, and elbows in special alloys such as Monel, Inconel, Hastelloy. We can manufacture elbows upto 48″ with wall thickness ranging from 1.5 mm thickness up to 40mm for varied sizes.
MSI Fittings are manufacturers, stockiest & suppliers of Concentric Reducer . Concentric Reducer have special quality finishing and duress for long life, high pressure and zero defects.
The product differentiation is based on the premier finish of Concentric Reducer with minimum burr at the edge .The v shape formation for perfect welding and fabrication of the fittings in mega projects in oil and gas industry for long life of the product.
Concentric Reducer is used in Petro-Chemical Industry, Oil and Gas Industry , Nuclear Industry, Pulp & Paper Indusry, Research & Development , Mega Projects & Defense & Development Industries. In fact wing to the special grade of steel 90 Degree Elbows are used for all critical applications.
What is a Pipe Reducer?
First, let’s keep it simple: A pipe reducer is a pipe fitting that connects a larger pipe to a smaller pipe. Thus, it reduces the size of the pipe in the pipe system, from one size to another. Pipe reducers may frequently be used to connect pipes of different sizes. There are a variety of reasons why this might be done, and there are a variety of materials that could be flowing through the pipe, which is why there are different types of pipe reducers.
Like other pipe fittings, it can be very complicated to find the right pipe reducer. The fit can be complicated, and materials will matter. But once you find the right pipe reducer, the installation should be fairly simple and fast.
When Would You Use a Pipe Reducer?
Reducers can be used simply to adapt pipes of other sizes, but there are also more complicated uses for them. They may need to be used when the flow has to be limited or expanded in a piping system, such as if the hydraulic nature of the piping system demands it. If you’re using a pipe reducer, you need to consider the consequences for the pipe system as a whole, because there will be changes in both flow and pressure.
Once you know that you need to use a pipe reducer, you need to make the decision between concentric and eccentric reducers. Most people are going to need to use a concentric pipe reducer, but there are some important reasons why an eccentric pipe reducer might be preferred.
Concentric vs Eccentric Reducer: What’s the Difference?
While this may seem complicated, it’s actually quite simple. Concentric reducers reduce the pipe in the center. So, if you’re looking at the reducer head-on, you can see the smaller section is formed in the direct center of the larger side. Eccentric reducers reduce the pipe to the side. So, if you’re looking at the reducer head-on, you can see the smaller section is against one side of the larger side.
This may seem like a very simple change, but it does matter.
The cone-shaped concentric pipe reducer means the pipes have matched center lines, and the eccentric reducer has mismatched center lines. Both of these have a consequence regarding flow. Most reducers are going to be concentric. Eccentric reducers are used when the pipes have to maintain the same top or bottom level. Eccentric reducers are frequently used to avoid trapping air within the system, so they are often used when both air and liquids may be flowing together.
Most people are going to need a cone-shaped concentric pipe reducer because they aren’t going to need one side of the reducer to remain flat. But in many applications, either can be used, as long as the bottom of the eccentric reducer is placed correctly. The major concern about eccentric reducers is that they can collect liquids or gasses in one area if they are not properly aligned. When used vertically, there is essentially no difference between a concentric or eccentric pipe reducer.
What About Concentric and Eccentric Expanders?
It should be noted that while they are called reducers, reducers by their very nature are also expanders. They are simply used in the opposite direction as expanders. Thus, expanders can also be both concentric and eccentric, and the consequences of using one or the other to expand rather than reduce are the same. Either way, they are being used when a pipe of one size has to transition to a pipe of another size.
How Are Reducers Installed?
How a reducer is installed depends on the material that the reducer and the pipes are made from. If the reducer and pipes are made from metal, they can be butt-welded together. If the reducers are made of PVC, they will likely be fitted and glued. There are reducers that may have push-to-fit or crimp installations as well. It depends on how the reducer was made, the material, and the goals for the reducer.
To install the reducer, the reducer will be fitted on both pipes and connected in the appropriate way. But care must be taken with eccentric reducers to ensure that the bottom of the eccentric reducer is properly lined up. In piping liquids horizontally, eccentric reducers need the flat side up, because otherwise, gasses can collect. But in piping vapors horizontally, eccentric reducers need the flat side down, because they need to avoid collecting liquids.
The more the pipe is reduced, the more concerns there may be related to flow. If the pipe is only being reduced a little, then there shouldn’t be any complications.
|Family||Buttweld Pipe Fitting||Shape||Concentric Reducer|
|Material||Stainless Steel||Make||MSI Fittings|
|Size||1/8″-48″||Thickness||SCH 5-SCH 160|
|Type||Seamless, Welded (ERW), Fabricated||Variation||Concentric|
|Finish||Short Blast, Sand Blast, Electro Polish||End||Bevelled|
|Marking||MSI Fittings Specs, Desc, Heat No||Packing||Protected by Cap|
Buttweld Pipe Reducer Production Range – Concentric & Eccentric
|Outside Diameter:||Seamless Pipe Tee ( 1/2″～24″), ERW / Welded / Fabricated Pipe Tee (1/2″～48″)
|Type:||Concentric Reducers, Eccentric Reducers
|Wall Thickness:||3mm – 40mm / SCH5, SCH10, SCH20, SCH30, SCH40, STD, SCH80, XS, SCH60, SCH80, SCH120, SCH140, SCH160, XXS
|Value Added Services:||Hot Dipped Galvanizing, Epoxy & FBE Coating, Electro Polish, Sand Blasting, Threading, Soldering
|Production Grades:||Stainless Steel, Alloy Steel, Duplex, Nickel Alloys, Low temperature Steel, Carbon Steel, Cupro Nickel, Copper
ASME: ANSI B16.9, ANSI B16.28, MSS-SP-43
DIN: DIN2605, DIN2615, DIN2616, DIN2617, DIN28011
EN: EN10253-1, EN10253-2
|ASTM A403||ASME SA403-Standard Specification for Wrought Austenitic Stainless Steel Piping Fittings
|ASME B16.9||Factory-Made Wrought Fittings Buttwelding|
|ASME B16.25||Buttwelding Ends ASME B16.28 – ‘Wrought Steel Short Radius Elbows and Buttwelding Returns|
|MSS SP-43||Wrought and Fabricated Butt-Welding Fittings for Low Pressure, Corrosion Resistant Applications|
BHEL approved stainless steel pipe fittings producers in Pune, Navi Mumbai, Nagpur, MSI Fittings carry an extensive range of butt weld and forged pipe fittings such as stainless steel reducer i.e. concentric & eccentric in various Size, NPT & Schedule (SCH)
We Have Ready Stock Of All Different Types Of Pipe Reducer, Eccentric Reducer, Concentric Reducer
We at MSI Fittings Manufacture stainless steel pipe fittings and stainless steel flanges according to ASME, EN, ISO and DIN standards. We are the first company in Pune, Navi Mumbai, Nagpur manufactured large size and fabricated stainless steel pipe fittings (upto 48”) for our european client & supplied around 30 ton Stainless Steel Reducers, Stainless Steel 5D/3D Elbow in just 10 days. since year 1999 we are manufacturing stainless steel pipe fitting in all High temperature grade including stainless steel 304/304L fittings, 316/316L/316Ti fittings, Duplex fittings, Super Duplex fittings, 904L fittings and other special steel grades like 2205 pipe fittings, ss 317L fittings, Inconel Pipe fittings, Hastelloy pipe fittings, Monel Pipe fittings. we manufacture stainless steel tube/pipe fittings in marine grade for marine applications, Our stainless steel pipe fittings are ideal for chemical processing, Dairy industry, Oil & gas Pipe line,Rigs,Ship Building etc. Our stainless steel pipe fittings are used in highly corrosive conditions.
Pipe Reducer Material Grades
|Stainless Steel Reducers:||ASTM A403 WP Gr. 304, 304H, 309, 310, 316, 316L, 317L, 321, 347, 904L
|Carbon Steel Reducers:||ASTM A 234 WPB , WPBW, WPHY 42, WPHY 46, WPHY 52, WPH 60, WPHY 65 & WPHY 70.
|Low Temperature Carbon Steel Reducers||ASTM A420 WPL3, A420 WPL6|
|Alloy Steel Reducers:||ASTM / ASME A/SA 234 Gr. WP 1, WP 5, WP 9, WP 11, WP 12, WP 22, WP 91|
|Duplex Steel Reducers:||ASTM A 815, ASME SA 815 UNS NO S31803, S32205. Werkstoff No. 1.4462|
|Nickel Alloy Reducers:||ASTM / ASME SB 336 UNS 2200 ( NICKEL 200 ), UNS 2201 (NICKEL 201 ), UNS 4400 (MONEL 400 ), UNS
8020 ( ALLOY 20 / 20 CB 3, UNS 8825 INCONEL (825), UNS 6600 (INCONEL 600 ), UNS 6601 ( INCONEL 601 ), UNS 6625 (INCONEL 625), UNS 10276 ( HASTELLOY C 276 )
Other Available Products Of Pipe Reducer, Eccentric Reducer, Concentric Reducer At Best Price
MSS SP-48 Welded Reducer Fittings Exporters
Concentric & Eccentric Reducer
MSS SP-43 Butt Weld Reducer
Low Tempreture Concentric & Eccentric Reducer
Austenitic stainless Steels Reducer Pipe Fittings Exporters
ASME / ANSI - B 16.9 Concentric Reducer
ANSI B16.28 Eccentric Reducer
ASME / ANSI - B 16.9 Reducer Pipe Fittings
High Yield Buttweld Reducer Fittings Manufacturers
Austenitic Stainless Steels Reducer Pipe Fittings
Galvanized Reducer (Concentric & Eccentric ) Stocks
Eccentric Reducer Butt Weld Pipe Fittings
Fabricated Buttweld Reducer Distributors
MSS SP-43 Eccentric (Bell) Reducer Dealer
ASME B16.25 Reducer Suppliers
Stainless Steel Buttweld Reducer Fittings
Stainless Steel Buttweld Reducer Fittings
Alloy Steel Reducer
Duplex Steel Reducer Pipe Fittings Manufacturers
Duplex Steel Reducer Pipe Fittings Leading Manufacturers
Concentric Reducer Butt Weld Pipe Fittings
Buttwelding Fittings MSS SP-75 Reducer Stockiest
ASME B16.28 Seamless Reducer Fittings Suppliers
ASME B16.25 Concentric & Eccentric Reducer
Why Choose MSI Fittings as Your Source for Seamless and Welded Pipe Reducer?
- 100% Tested Pipe Reducer: All our products pass testing requirements of international manufacturing specification. Pipe Reducer are produced by ISO 9001 certified factory, and shipped with MTC as per EN 10204 3.1
- Best Price Guaranteed for Pipe Reducer: When you source MSI Fittings Industries, you source everything directly from the manufacturer and stockholder! We have an average daily sale volume of around 40 tons of steel pipes and tubes from our stock. We believe in offering our customer’s high quantity discounts and work closely with them on all their project requirements. We always offer the most competitive prices for Pipe Reducer to both prospective and existing customers.
- Fast Quotations and Delivery: We understand your need for purchasing materials with short lead times. We have extensive stocks of standard size Pipe Reducer, enabling us to deliver goods on an immediate basis to all our customers in Pune, Navi Mumbai, Nagpur and overseas.
- Quality Raw Materials: We use high quality raw materials to produce Pipe Reducer seamless and welded. Our raw materials are quality tested before being used in production of final product. We can also offer stage wise inspection for lap joint stub end.
- Standard and Non Standard Sizes for Pipe Reducer: We can offer Pipe Reducer in both standard and non standard sizes with shortest delivery times.
- Complete Documentation: We provide complete product related documents to our customers before delivery of the goods.
Pipe Reducer:- (i) Eccentric (ii) Concentric
|What is a Pipe Reducer?||
A pipe reducer is a pipe fitting that connects a larger pipe to a smaller pipe. Thus, it reduces the size of the pipe in the pipe system, from one size to another.
|Advantages of use of Buttweld Fittings||
A piping system using buttweld fittings has many inherent advantages over other forms.
-Carbon Steels: A234/A234M Gr. WPB
1.) ASME/ASTM – ASME B16.9, ASME B16.28, ASME B16.49, ASME B16.25, ISO3419, ANSI/AWWA C208, MSS SP 75
Seamless: 1/2" – 24"
1.65mm to 80mm, SCH 5, SCH 10, SCH 40, SCH 80, SCH 100, SCH XS, SCH XXS, Custom Thickness
Seamless, Welded, 100% X-Ray Welded or Fabricated, Miter Bends
Shot blasting, Black Phosphating, Black, Oiled, Paint, Hairline, Mirror, Galvanized, Anti Corrosive
US$7.5/PC to $2000/PC
|Port of Shipment||
India or China
ISO 9001 : 2015, ISO 14001:2015, OHSAS 18001:2015, PED 97/23/EC
Hardness Test, Ultrasonic Testing , IGC Test
All products would be Heat Treated, if required by the standard.
|Quality Control & Inspection||
Machanical Testing in own labs with Tensile Strength, Yield Strength, Elongation, Hardness, Impact, Mictrostruture etc.
Plain, Bevel, Screwed, Threaded
|International Standards & Codes Applicable||
-ANSI B 16.5: Pipe Flanges and Flanged Fittings.
Carbon Steel Pipe Reducer, Stainless Steel Pipe Reducer, Alloy Steel Pipe Reducer, Duplex Pipe Reducer, Super Duplex Pipe Reducer, Copper Nickel Pipe Reducer, Nickel Alloys Pipe Reducer.